Safes with this Lock:

1. Mesa MBF1512E Burglary & Fire Safe
2. Mesa MBF2020E Burglary & Fire Safe
3. Mesa MBF2620E Burglary & Fire Safe
4. Mesa MBF3820E Burglary & Fire Safe
5. Mesa MBF5922E Burglary-Fire Gun Safe
6. Mesa MBF5922E-P Burglary & Fire Safe
7. Mesa MBF6032E Burglary-Fire Gun Safe
8. Mesa MBF6032E-P Burglary & Fire Safe
9. Mesa MBF7236E Burglary-Fire Gun Safe
10. Mesa MBF7236E-P Burglary & Fire Safe

 

IMPORTANT:

• To ensure the safety of your belongings, you MUST change the factory set User Codes to your own unique codes immediately!

 

FEATURES:

Two Code Capacity

• User 1 Code: Factory Set
• User 2 Code: Factory Set

Lock-Out Penalty

• Five Beeps Lockout Penalty
• If three invalid codes are entered in a row, the keypad will shut down for a period of fifteen (15) minutes.
• During this shut down period the keypad will not accept any codes.

Two User Codes

• Two User Codes can be programmed up to eight (8) digits long.
• Please change both codes immediately for your safety.

 

OPERATING INSTRUCTIONS:

Always Perform this operation with the door open

• Before closing the door, make sure all the changes are correct.

Quick Start

• Install a 9-Volt Battery
• Enter: [factory set Code x - x - x - x - x - x - x - x - #]
  Green light will turn on.
• Turn handle before the green light turns off
• To lock your safe, close door & turn handle back to the locked position

 

IMPORTANT:

• Always make sure your safe is locked before walking away!

• If your code is correct a green light will turn on for approximately 5 seconds & you will hear a 'Click'

• If the code is in incorrect a red light will turn on, followed by 5 'Beeps'

 

NOTE:

• Be sure to press firmly & ONLY use your finger tips to press the keys on the keypad. DO NOT USE your finger nail, a pen, etc. This will damage the keys

Safe Operation & Programming

• 1st USER CODE is factory set : [factory User Code 1: x - x - x - x - x - x - x - x - #]
• 2nd USER CODE is factory set : [factory User Code 2: x - x - x - #]
  Please see your user manual for the factory set User Codes or contact Tech Support.

IMPORTANT:

• To ensure the safety of your belongings, you MUST change the factory set User Codes to your own unique codes immediately!

 

How To Open Your Safe

• Input : Code-# [light stays green for 5 seconds]
• Turn handle to the unlocked position before the green light disappears
  Example: 1-2-3-#
  Invalid Code: 5 'Beeps'

Wrong Try Penalty

• If 3 wrong codes are entered consecutively, the keypad will shut down for a period of 15 minutes. During this shut down period, the keypad will not accept any codes

Changing the 1st User Code

• Locate the red button on the inside hinge side edge of door
• Press the red button [Lock will 'Beep' 2 times with the yellow light on]
• Input: Your New Code-* [Lock will 'Beep' 2 times]
  Unsuccessful Code Change: 5 'Beeps' [the old code is still valid; repeat steps 1-3]

NOTE:

• Test the new codes several times before closing the door.

Changing the 2nd User Code

• Locate the red button on the inside hinge side edge of door
• Input: 0-0 on the keypad & Press the red button [Lock will 'Beep' 2 times with the yellow light on]
• Input: Your New Code-* [Lock will 'Beep' 2 times]
  Unsuccessful Code Change: 5 'Beeps' [the old code is still valid; repeat steps 1-3]

 

NOTE:

• Test the new codes several times before closing the door.

 

Low Battery Warning

• Red light appears when you open the safe other than the green light.
• Enter your code and get valid response but the lock doesn't unlock.

Changing the Batteries

• Locate the battery cover on the bottom edge of the keypad and remove the cover by pulling on the tab.
• Carefully and gently remove the 9-volt battery from the compartment.
  CAUTION! Hold onto battery connector to avoid pulling wires out of housing.
• Carefully reinsert the new 9V alkaline battery, do not force the battery into the compartment.
• The lock will retain all current codes and settings.